There are a lot of pieces that go into assembling a sliding door track system for each horse stall door. This page is dedicated to any replacement part you may want or need for the Cambridge horse stall series. We offer a Cambridge Premium track stall door kit that includes everything you need for a Cambridge sliding stall door.
Showing all 19 results
The Cambridge door latch bar is installed opposite the door latch filler bar. Simply, insert the latch bar through the top of the stall door with the spring between the channel and cotter pin.
Compatibility: Cambridge Stalls
The Cambridge door latch filler bar is installed over the guide post, opposite the door latch bar. Be sure the filler bar is seated completely down – use a block of wood and hammer/rubber mallet if necessary to tap the filler bar down.
Compatibility: Cambridge Stalls
Everything you need to mount your Cambridge horse stall door is included in this Cambridge Premium track door hardware kit, including the 8′ Premium track itself, end caps, mounting brackets, trolleys, and more!
Compatibility: Cambridge Stalls
The Cambridge Premium track door hardware kit includes the components needed to hang a Cambridge horse stall door, excluding the door itself and the 8′ Premium track.
Compatibility: Cambridge Stalls
The door latch bar spring is used in our “One Touch” Premium track system. For installation, insert the door latch bar through the top of the door with the door latch bar spring between the channel and cotter pin.
The Premium track trolley is used for hand-sliding stall doors in the 8′ Premium track. There is no metal-to-metal contact, meaning this system functions very quietly. Sold individually, two trolleys and bolts are needed per door.
Compatibility: Premium Track Offset Trolley Bolt
Protect your sliding stall door hardware with these Premium Track End Caps. Designed to seal off the open ends of your overhead track, they prevent accumulating dust, hay, and barn debris from jamming your door trolleys. They also keep small pests like birds and mice from nesting inside the track. Available in your choice of Galvalume (metallic) or Powder-Coated Black.
Please note: Sold individually. Two (2) end caps are required to complete a new track installation.
Track: 8′ Premium Track
Proudly Made in the USA. No imported horse stalls—just American craftsmanship you can trust.
The post bumper is made of heavy-duty solid steel and is compatible with doors that are up to 1½” thick. It keeps the door tight to the stall front and won’t allow it to swing outward while closed. Available in a hot-dipped galvanized or powder-coat paint finish.
Door Compatibility: Accommodates doors up to 1½” thick.
Ensure smooth and safe operation of your sliding barn doors with this heavy-duty Stall Door Stay Roller. Designed to keep sliding doors up to 1½” thick perfectly aligned with their track, it prevents doors from being pushed or kicked out by your horses. Featuring a non-marking plastic guide wheel, it is compatible with Cambridge, Derby, Essex, and Oxford stall systems. Available in your choice of Galvalume or Powder-Coated Black finishes.
Proudly Made in the USA. No imported horse stalls—just American craftsmanship you can trust.
Securely install your sliding door guides with the 1/4″ x 1-1/2″ Phillips Pan Head Stay Roller Screw. Purpose-built for barn environments, these heavy-duty fasteners are available in your choice of a rust-resistant zinc-plated or sleek powder-coated black finish to match your aesthetic.
Please note: This item is sold individually. Three (3) screws are required to complete a standard stay roller installation.
Compatibility: Stay Roller
Proudly Made in the USA. No imported horse stalls—just American craftsmanship you can trust.
This #8 x 1″ Phillips pan head Tek self-drilling clip screw has a zinc-plated finish for rust protection. Sold individually, this screw is used in several RAMM horse stall series installations.
The neoprene o-ring is used with our door latch filler bar – two required for installation. The o-rings slide over the guide post and should be approximately 1″ from the bottom and 1/2″ from the top.
Compatibility: Cambridge Stalls
The latch bar cotter pin is used in the “One Touch” Premium track system. For installation, insert the door latch bar through the top of the door with the latch bar spring between the channel and cotter pin.
Speed up your stall installation with the #14 x 1″ Phillips Pan Head Tek Self-Drilling Clip Screw. Featuring a built-in drill point for effortless installation and a heavy-duty zinc-plated finish for superior rust protection, this premium fastener is built for tough barn environments. It is an essential hardware component used across several RAMM horse stall series installations.
Please note: This item is sold individually as a replacement part or add-on.
Proudly Made in the USA. No imported horse stalls—just American craftsmanship you can trust.
Securely mount your horse stall sliding doors with our Premium Track Bracket Screws. Specifically designed to install premium track brackets for hanging the 8′ Premium track, these #10 x 1.5″ fasteners feature a Phillips pan head and a heavy-duty zinc-plated finish for exceptional rust protection.
Please note: Sold individually. These screws are exclusively compatible with our Premium track brackets.
Proudly Made in the USA. No imported horse stalls—just American craftsmanship you can trust.
The Premium Track Front Mount Bracket securely supports RAMM’s 8′ Premium Track, providing a strong, stable mounting point for smooth, dependable sliding door operation. Manufactured from heavy-duty galvanized steel for superior strength and corrosion resistance, this bracket is designed to withstand the demands of daily use in horse barns and agricultural facilities. Compatible with RAMM Derby and Cambridge horse stall systems, it can also be used with a variety of sliding barn door applications.
Please Note: Brackets are sold individually. Seven (7) front mount brackets are required to properly support one 8′ Premium Track. Mounting screws are sold separately.
Trolly bolt is used with the trolly and track to adjust and make sliding door plum, as well as adjust the space between the door post and door.
Compatibility: Premium Track Trolley
The Premium track latch catch bracket works with the spring bar latch for the Premium track system. Compatible with the Cambridge, Dublin and Nobleman horse stalls.
The 5/16″ x 1-1/2″ hex head lag screw is used to secure stall components such as the post bumper, door latch handle, and more. Two lag screws are required for both installations. Sold individually.
Loading...
Your cart is currently empty!
Notifications
